In this guide
- Common Causes Of A Keystone Furnace Not Lighting
- Thermostat And Controller Settings
- Electrical Power And Breakers
- Gas Supply And Ignition System
- Airflow And Safety Switches
- Dirty Burners Or Flame Sensor
- Step-By-Step Troubleshooting Guide
- Safety Considerations
- When To Call A Professional
- Maintenance Tips To Prevent Future Issues
Keystone furnaces, like many gas-fired units, can fail to light for a variety of reasons. This guide outlines the most common causes and practical fixes to help homeowners diagnose and address a Keystone furnace that won’t light. It covers thermostat and control issues, power and gas considerations, ignition and airflow problems, and when to call a professional. Prioritize safety: if there is a gas smell, hissing, or you’re unsure about any step, shut off power and contact a licensed HVAC technician.
While some checks are simple, others involve gas and electrical components that require professional service. The goal is to restore reliable heat while minimizing risk and preventing future outages through proper maintenance and safe handling.
Common Causes Of A Keystone Furnace Not Lighting
Thermostat And Controller Settings
A thermostat that isn’t calling for heat is a frequent reason a Keystone furnace won’t light. Verify the thermostat is set to Heat and the setpoint is higher than the room temperature. If it is a programmable or smart thermostat, confirm the schedule is calling for heat and that the device is communicating with the furnace. Loose or corroded wiring between the thermostat and furnace control board can also interrupt the heat call.
Tip: If the thermostat is battery-powered, replace the batteries and confirm the display is active. A tripped compatibility setting in a smart thermostat can mimic a non-call for heat.
Electrical Power And Breakers
Furnaces rely on a dedicated electrical circuit. Check the main panel for a tripped breaker or blown fuse. Reset the breaker and see if the furnace starts. Also inspect the furnace’s on/off switch, usually located on the unit’s exterior or near the blower compartment. If the breaker trips again after reset, stop and call a professional, as repeated trips can indicate a short or overload that requires diagnosis and repair.
Note: Power surges or loose wiring can also prevent ignition. Do not bypass safety switches or force components to operate if the electrical system shows signs of damage.
Gas Supply And Ignition System
Gas supply must be open for the furnace to ignite. Ensure the gas valve is fully open and that other gas appliances in the home are functioning. A closed valve or an interrupted gas supply prevents ignition. The ignition system—whether an electronic spark or a hot surface igniter—must function properly. If the igniter does not glow or spark, ignition will fail even if gas is present.
Safety reminder: If you smell gas, hear a hissing sound, or suspect a leak, turn off the gas supply, evacuate, and contact the utility or fire department immediately. Do not attempt to relight the furnace yourself.
Airflow And Safety Switches
Restricted airflow can prevent ignition or trigger safety shutoffs. Check the air filter and replace it if dirty. Ensure all supply registers and return vents are open and unobstructed. The furnace has safety switches, including a limit switch and roll-out switches; if these are triggered, the furnace will not light. A blocked vent or blocked air path often causes these switches to trip, requiring inspection and correction before relighting.
Observation: Poor ductwork or blocked exterior exhaust can also prevent safe operation and require a professional assessment.
Dirty Burners Or Flame Sensor
Over time, burners can accumulate dust or corrosion, and the flame sensor can become coated with residue. A dirty sensor may fail to establish a flame even when the igniter is functioning. Cleaning and servicing these parts can restore ignition but should be done by a trained technician if you are not experienced with gas appliances. When in doubt, schedule service to avoid damaging components or creating safety risks.
Important: Do not attempt deep cleaning of gas burners or the flame sensor without proper training and tools.
Step-By-Step Troubleshooting Guide
-
Check power at the furnace: Confirm the furnace has power, the on/off switch is in the ON position, and the circuit breaker is not tripped. If the switch has no power or the breaker trips repeatedly, stop and call a professional.
-
Inspect the thermostat: Verify Heat is selected and the setpoint is sufficiently above room temperature. Replace batteries if applicable, and ensure the thermostat is communicating with the furnace. Reset the thermostat if needed.
-
Verify gas supply: Ensure the gas valve is open and the gas line is delivering fuel to the furnace. If other gas devices aren’t functioning or you smell gas, evacuate and contact the gas utility or emergency services.
-
Listen to the ignition sequence: When the furnace tries to light, listen for the igniter glow or spark. If you don’t hear ignition or see a glow, the ignition module or igniter may need replacement by a professional.
-
Check flame establishment: If the igniter glows but the flame does not establish, the flame sensor may be dirty or the gas valve may not be delivering gas. Do not bypass safety sensors; call a technician for diagnosis and cleaning if needed.
-
Review diagnostic codes: Many Keystone units display LED blink codes or fault codes on the control board. Note the pattern and consult the manual or a technician to interpret and address the specific fault.
-
Assess airflow and drainage: Verify filters are clean, vents are open, and condensate traps are clear. Poor airflow or blocked drainage can prevent safe ignition and trigger shutdown.
Safety Considerations
-
Gas smell or hissing means immediate action: leave the area, avoid lighting flames, and call your gas provider or emergency services.
-
Carbon monoxide risk: If CO detectors alarm, leave the home and seek fresh air, then call emergency services.
-
Electrical safety: Do not bypass breakers or safety switches. If wiring appears damaged or warm, stop and call a licensed electrician or HVAC tech.
When To Call A Professional
-
You smell gas or detect a persistent gas odor.
-
Repeated tripped breakers or electrical smells occur.
-
No ignition after checking igniter, burner, and sensor.
-
Error codes you cannot interpret or fix with basic steps.
-
Uncertainty about performing gas work or handling combustion components.
Maintenance Tips To Prevent Future Issues
-
Schedule annual professional maintenance: A technician should inspect burners, igniter, flame sensor, control board, and safety switches yearly.
-
Replace filters regularly: A clean filter improves airflow and combustion efficiency, reducing ignition problems.
-
Keep vents and condensate lines clear: Ensure outdoor exhausts and condensate drains are free of obstructions.
-
Test thermostat accuracy: Periodically verify that the thermostat calls for heat and maintains accurate temperatures.
-
Replace worn components: Igniters, flame sensors, and ignition controls wear with age; schedule replacement as part of planned maintenance to avoid sudden outages.